Best in the New Yeat to all.
Going to change my engine and thinking of buying a new one rather than rebuilding my old one.
My transfercase, transmission and radiator are new and the rest of the vehicle i9s in good shape.
Any suggestions for add on's. Improve milage,two wheel to four wheel drive, trans mission coolers ect ect.
Bob Fitz
2004 H1 Diesel
- Hesh
- CHC Trail Guide
- Posts: 527
- Joined: Sun May 02, 2010 3:00 pm
- Location: Winnipeg
Re: 2004 H1 Diesel
What is wrong with the current motor?
[center]November '10 CHC ROTM Winner!!![/center]
- AmpGramp
- Club Member
- Posts: 21
- Joined: Wed Aug 20, 2008 8:39 pm
Re: 2004 H1 Diesel
[quote name='Hesh' timestamp='1326955599' post='34525']
What is wrong with the current motor?
[/quote]
Rad problems, over heated.
Toyed with conversion but leaning towards replacing with same type. Cheaper and with extra cash want to throw some extra improvements at it.
Bob Fitz
What is wrong with the current motor?
[/quote]
Rad problems, over heated.
Toyed with conversion but leaning towards replacing with same type. Cheaper and with extra cash want to throw some extra improvements at it.
Bob Fitz
- paulg
- CHC Navigator
- Posts: 80
- Joined: Tue Mar 25, 2008 10:56 pm
- Location: Vancouver, BC.
Re: 2004 H1 Diesel
if you are going to swap it with another 6.5L you should look at the P400 series motor from GEP, a lot of improvements etc and most of the accessories from your current motor will swap over.
Big thing to make sure of when shopping for a new motor is that it will accept a center mount Turbo, the 6.5L blocks from the pickup trucks are designed for side mount turbos.
Big thing to make sure of when shopping for a new motor is that it will accept a center mount Turbo, the 6.5L blocks from the pickup trucks are designed for side mount turbos.
[center]Lifes a bummer if your not driving a Hummer...[/center]
[left]2001 black HMCS
40" XTerrains on 17" 2 piece Hutchinsons with Beadlocks
3" bodylift
Heath Programed ECU
Heath Manual wastegate controller (turbomaster)
Walking J feed the beast Fuel line upgrade
Remote PMD
CMGS water\meth injection
Rear head cooling kit
Provent 200 Oil Vapor seperator
Scangage II
Boost, EGT, Temp gauges.
Dynamat extreme
dual optima red tops
Straight piped exhaust[/left]
[left]2001 black HMCS
40" XTerrains on 17" 2 piece Hutchinsons with Beadlocks
3" bodylift
Heath Programed ECU
Heath Manual wastegate controller (turbomaster)
Walking J feed the beast Fuel line upgrade
Remote PMD
CMGS water\meth injection
Rear head cooling kit
Provent 200 Oil Vapor seperator
Scangage II
Boost, EGT, Temp gauges.
Dynamat extreme
dual optima red tops
Straight piped exhaust[/left]
- AmpGramp
- Club Member
- Posts: 21
- Joined: Wed Aug 20, 2008 8:39 pm
Re: 2004 H1 Diesel
[quote name='paulg' timestamp='1327001275' post='34538']
if you are going to swap it with another 6.5L you should look at the P400 series motor from GEP, a lot of improvements etc and most of the accessories from your current motor will swap over.
Big thing to make sure of when shopping for a new motor is that it will accept a center mount Turbo, the 6.5L blocks from the pickup trucks are designed for side mount turbos.
[/quote]
Thanks for the Info. Who is GEP ?
Bob Fitz
if you are going to swap it with another 6.5L you should look at the P400 series motor from GEP, a lot of improvements etc and most of the accessories from your current motor will swap over.
Big thing to make sure of when shopping for a new motor is that it will accept a center mount Turbo, the 6.5L blocks from the pickup trucks are designed for side mount turbos.
[/quote]
Thanks for the Info. Who is GEP ?
Bob Fitz
- Hesh
- CHC Trail Guide
- Posts: 527
- Joined: Sun May 02, 2010 3:00 pm
- Location: Winnipeg
- AmpGramp
- Club Member
- Posts: 21
- Joined: Wed Aug 20, 2008 8:39 pm
Re: 2004 H1 Diesel
[quote name='Hesh' timestamp='1327031739' post='34549']
http://www.optimizer6500.com/
[/quote].
Interesting stuff, nice to have a site like this
Where would I inquire about availablty and cost?
Bob Fitz
http://www.optimizer6500.com/
[/quote].
Interesting stuff, nice to have a site like this
Where would I inquire about availablty and cost?
Bob Fitz
- dwaxman1
- CHC Trail Guide
- Posts: 957
- Joined: Wed Dec 09, 2009 6:20 pm
- Location: , Ontario
- Roy
- CHC Trail SuperGuide
- Posts: 1933
- Joined: Tue Dec 29, 2009 8:21 pm
- Location: Stratford,Ontario
Re: 2004 H1 Diesel
Check on warranty's, if you can get a 5 yr warranty go for it, Most rebuilders give 1 yr limited. With any conversion, you loose something, <img src='http://www.canadianhummerclub.com/forum ... ngHead.gif' class='bbc_emoticon' alt=':banghead:' />
99 Wagon
5.9 Cummins 12 valve mech. Stocking most parts to fix your H1
41.5-13.5 R16.5 Pitbull Rockers,
Auburn lockers front and rear
Full custom underbody protection
3" body lift
4" side rock tubes
12100 rear cv shafts
5.9 Cummins 12 valve mech. Stocking most parts to fix your H1

41.5-13.5 R16.5 Pitbull Rockers,
Auburn lockers front and rear
Full custom underbody protection
3" body lift
4" side rock tubes
12100 rear cv shafts
519-272-1761 
<p style="text-align:center;"> 