Wrenching Party ! 2018

Here is a great place to Post events in your Area!!
User avatar
GreenMeanie
CHC Pilot
Posts: 426
Joined: Tue Jul 22, 2008 3:28 am

Re: Wrenching Party ! 2018

Post by GreenMeanie »

Well, i was almost going to postpone coming today. When i do runs over 50 clicks i always check the truck for basics. Raising the wheels and giving them a wiggle to check and i found both my rear upper ball joints were loose, passenger side was really loose, meaning the four locknuts holding the ball joint in had some play. I got them as tight as i could with hand tools but they need to be torqed down with air for sure. At first i was thinking spindle nut issue as im using the stock ones. In fact the drivers side rear does seem to have some spindle play. might have to check that today if we have time. I made a video but no time to post it. I found this out a 4 am when i got to the shop and started running my checks. I thought i was toast for showing up today but i think i will be ok. Im going to take it easy getting there and may leave a little earlier. Its 6;15 now so i should still be there on time.
Lesson for the day is check check check. Sure glad i did.
Early 1997 HMC4, 1 of 35, Original Block H296, 110,000 miles and no cracks yet, G10 green
Custom made Brush Gaurd, Roof Rack, Overhead Console and Sound System.
User avatar
Monk
CHC Trail SuperGuide
Posts: 1232
Joined: Mon Oct 01, 2012 10:36 am
Location: Ontario

Re: Wrenching Party ! 2018

Post by Monk »

Very smart move for any longer trip :)

Always good to be on top of things,ever since my Frame change I was under her nightly for a while,...





see yous there today as well..
96 HMC4

Optimizer N/A

Super Swamper IROKS 39.5x13.5x 16.5
User avatar
ddgermann
CHC Pilot
Posts: 299
Joined: Sat Jun 15, 2013 11:07 pm
Location: Edmonton

Re: Wrenching Party ! 2018

Post by ddgermann »

Hope you guys have a good day.
 
Having my own little wrenching party here out west...
 
Both vehicles in yesterday. I managed to get the Corvette out till Monday so I at least have something to drive this weekend. Just getting a few carbon fiber bits installed. The Hummer will be in for a while. Needs a front blower motor "again", a block heater and I've got a small parasitic power drain to find.
 
Would have rather spent the day with you fellas.
 
Hope you get everything fixed up over there guys.
why upside down?... no idea
IMG_9545.JPG
IMG_9546.JPG
You do not have the required permissions to view the files attached to this post.
Last edited by ddgermann on Sun Jul 08, 2018 3:16 pm, edited 1 time in total.
1999 H1 HMC4 (black on black)
 
Hummer: from The Century Dictionary and Cyclopedia. n.[font=inherit;font-size:.9em;font-style:inherit;font-weight:inherit] "One who, or that which excels in any quality, especially in general energy or speed."[/font]
User avatar
Monk
CHC Trail SuperGuide
Posts: 1232
Joined: Mon Oct 01, 2012 10:36 am
Location: Ontario

Re: Wrenching Party ! 2018

Post by Monk »

Lol I don't know how to fix the rotation thing on my iPad so now your truck is always upside down hahaha.

Got to admit your vehicles look pretty sweet
96 HMC4

Optimizer N/A

Super Swamper IROKS 39.5x13.5x 16.5
User avatar
Monk
CHC Trail SuperGuide
Posts: 1232
Joined: Mon Oct 01, 2012 10:36 am
Location: Ontario

Re: Wrenching Party ! 2018

Post by Monk »

Well Saturday has come and gone and it was nice out there.

I showed up in the a.m. to replace some window switches and my air filter clamp, so now no tools needed to change my air filter.

Next time I go there I will have to fix a minor seal leak in my rear passenger output shaft and possibly look for an air leak I think would be my passenger side as well front.



Greenmeanies truck was on the Hoist when I got there. (Nice truck) the man did a hell of a lot of work on that truck as you can see every Bolt & Nut has been pulled off and put back on.



Here are some pics of his truck when I showed up
You do not have the required permissions to view the files attached to this post.
Last edited by Monk on Sun Jul 08, 2018 9:57 am, edited 1 time in total.
96 HMC4

Optimizer N/A

Super Swamper IROKS 39.5x13.5x 16.5
User avatar
Monk
CHC Trail SuperGuide
Posts: 1232
Joined: Mon Oct 01, 2012 10:36 am
Location: Ontario

Re: Wrenching Party ! 2018

Post by Monk »

Plus it's kind of nice to see Parts on that you think about putting on in person.

Lol, it's sort of gives me a chance to size up the job in my head like when I saw his power master starter
96 HMC4

Optimizer N/A

Super Swamper IROKS 39.5x13.5x 16.5
User avatar
GreenMeanie
CHC Pilot
Posts: 426
Joined: Tue Jul 22, 2008 3:28 am

Re: Wrenching Party ! 2018

Post by GreenMeanie »

Fun times!! Really appreciate Roy's time and efforts putting this on.
I'm adding my 4am video of the issue that nearly prevented me from showing up 
https://youtu.be/qKEDLK4pBWg
Early 1997 HMC4, 1 of 35, Original Block H296, 110,000 miles and no cracks yet, G10 green
Custom made Brush Gaurd, Roof Rack, Overhead Console and Sound System.
User avatar
Monk
CHC Trail SuperGuide
Posts: 1232
Joined: Mon Oct 01, 2012 10:36 am
Location: Ontario

Re: Wrenching Party ! 2018

Post by Monk »

Does the link work for anyone else?
96 HMC4

Optimizer N/A

Super Swamper IROKS 39.5x13.5x 16.5
User avatar
GreenMeanie
CHC Pilot
Posts: 426
Joined: Tue Jul 22, 2008 3:28 am

Re: Wrenching Party ! 2018

Post by GreenMeanie »

Should work now. I forgot to publish it LOL
Early 1997 HMC4, 1 of 35, Original Block H296, 110,000 miles and no cracks yet, G10 green
Custom made Brush Gaurd, Roof Rack, Overhead Console and Sound System.
User avatar
Monk
CHC Trail SuperGuide
Posts: 1232
Joined: Mon Oct 01, 2012 10:36 am
Location: Ontario

Re: Wrenching Party ! 2018

Post by Monk »

Haha! You sir are a die hard..

Up at 4am for a wrench party? I'm wiping drool off my pillow that early on a Saturday.



Seriously though , that movement would make me think twice as well. Especially the distance you drove.

Nice seeing ya again on sat.



Hummer Roy errrrr I mean,

Captain Roy does know his stuff, and really does help with do it a yourselfers , I've learned a lot from him,
96 HMC4

Optimizer N/A

Super Swamper IROKS 39.5x13.5x 16.5
Post Reply